Reconciling Structural Detectability and Dynamic Alarm Performance in a Simulated Continuous Stirred-Tank Reactor
Downloads
Abstract
Structural analysis identifies whether model equations can, in principle, generate diagnostic consistency checks, whereas a dynamic detector quantifies whether implemented residuals produce timely alarms under noise. The two layers are often compared as if they shared an information boundary. This paper shows why that assumption can fail and develops an information-consistent reconciliation using a simulated two-state jacketed Continuous Stirred-Tank Reactor (CSTR). Four measurement configurations, four single faults and four joint measurement-noise multipliers are examined. The supplied study reports 50 noise realizations per fault condition and 64 threshold-sweep Areas Under the Curve (AUCs). We first audit the one-interval Dulmage–Mendelsohn (DM) model and the Savitzky–Golay/Cumulative Sum (CUSUM) detector against the exact information available to each. The structural graph treats commanded feed flow and coolant temperature as unknown, while the detector substitutes both commands into balance residuals. Two proposed input-estimation residuals are proved to be algebraic rescalings of those same command-substituted balances; they add no independent analytical redundancy. In addition, one scalar independent residual cannot produce four distinct nonempty binary fault signatures, so the reported isolability for the coolant-measured configuration is not established. A descriptive reanalysis of the source-reported values nevertheless identifies stable empirical patterns: Mean AUC falls from 0.969 at half noise to 0.812 at fourfold noise; fouling is the dominant weak case (overall mean 0.690); and measuring flow preserves high-noise feed-flow-bias performance (AUC 0.927–0.937 versus 0.732–0.740 without flow). These values are not independently reproduced because the named code and run-level outputs were not supplied. The paper contributes an information-parity principle, an explicit residual-independence test, and a staged validation protocol that separates structural possibility, realizable residual construction, statistical calibration and empirical generalization. The resulting interpretation is narrower but scientifically stronger: sensor value and weak-fault behavior can be discussed descriptively, while structural–dynamic agreement and complete isolation remain hypotheses for a command-consistent computational rerun.
Keywords
Model-based fault diagnosis Structural analysis Dulmage–mendelsohn decomposition analytical redundancy Continuous stirred-tank reactor Cumulative Sum Fault isolability ReproducibilityReferences (32)
- [1] Venkatasubramanian, V., Rengaswamy, R., Yin, K., & Kavuri, S. N. (2003). A review of process fault detection and diagnosis: Part I: Quantitative model-based methods. Computers & Chemical Engineering, 27(3), 293–311. https://doi.org/10.1016/S0098-1354(02)00160-6
- [2] Venkatasubramanian, V., Rengaswamy, R., & Kavuri, S. N. (2003). A review of process fault detection and diagnosis: Part II: Qualitative models and search strategies. Computers & Chemical Engineering, 27(3), 313–326. https://doi.org/10.1016/S0098-1354(02)00161-8
- [3] Venkatasubramanian, V., Rengaswamy, R., Kavuri, S. N., & Yin, K. (2003). A review of process fault detection and diagnosis: Part III: Process history based methods. Computers & Chemical Engineering, 27(3), 327–346. https://doi.org/10.1016/S0098-1354(02)00162-X
- [4] Frank, P. M. (1990). Fault diagnosis in dynamic systems using analytical and knowledge-based redundancy: A survey and some new results. Automatica, 26(3), 459–474. https://doi.org/10.1016/0005-1098(90)90018-D
- [5] Isermann, R. (2005). Model-based fault-detection and diagnosis--status and applications. Annual Reviews in Control, 29(1), 71–85. https://doi.org/10.1016/j.arcontrol.2004.12.002
- [6] Isermann, R. (2006). Fault-diagnosis systems: An introduction from fault detection to fault tolerance. Springer Berlin, Heidelberg. https://doi.org/10.1007/3-540-30368-5
- [7] Chen, J., & Patton, R. J. (1999). Robust model-based fault diagnosis for dynamic systems. Springer New York, NY. https://doi.org/10.1007/978-1-4615-5149-2
- [8] Ding, S. X. (2013). Model-based fault diagnosis techniques: Design schemes, algorithms and tools. Springer London. https://doi.org/10.1007/978-1-4471-4799-2
- [9] Blanke, M., Kinnaert, M., Lunze, J., & Staroswiecki, M. (2015). Diagnosis and fault-tolerant control. Springer. https://doi.org/10.1007/978-3-662-47943-8
- [10] Chiang, L. H., Russell, E. L., & Braatz, R. D. (2001). Fault detection and diagnosis in industrial systems. Springer London. https://doi.org/10.1007/978-1-4471-0347-9
- [11] Gertler, J. (1998). Fault detection and diagnosis in engineering systems. Marcel Dekker. https://www.routledge.com/Fault-Detection-and-Diagnosis-in-Engineering-Systems-1st-Edition/Gertler/p/book/9780203756126
- [12] Russell, E. L., Chiang, L. H., & Braatz, R. D. (2000). Fault diagnosis in chemical processes using Fisher discriminant analysis, discriminant partial least squares, and principal component analysis. Chemometrics and Intelligent Laboratory Systems, 50(2), 243–252. https://doi.org/10.1016/S0169-7439(99)00061-1
- [13] Russell, E. L., Chiang, L. H., & Braatz, R. D. (2001). Data-driven methods for fault detection and diagnosis in chemical processes. Springer London. https://doi.org/10.1007/978-1-4471-0347-9
- [14] Joe Qin, S. (2003). Statistical process monitoring: Basics and beyond. Journal of Chemometrics: A Journal of the Chemometrics Society, 17(8–9), 480–502. https://doi.org/10.1002/cem.800
- [15] Gao, Z., Cecati, C., & Ding, S. X. (2015). A survey of fault diagnosis and fault-tolerant techniques—Part I: Fault diagnosis with model-based and signal-based approaches. IEEE Transactions on Industrial Electronics, 62(6), 3757–3767. https://doi.org/10.1109/TIE.2015.2417501
- [16] Dulmage, A. L., & Mendelsohn, N. S. (1958). Coverings of bipartite graphs. Canadian Journal of Mathematics, 10, 517–534. https://doi.org/10.4153/CJM-1958-052-0
- [17] Krysander, M., & Nyberg, M. (2002). Structural analysis for fault diagnosis of DAE systems utilizing MSS sets. IFAC Proceedings Volumes, 35(1), 143–148. https://doi.org/10.3182/20020721-6-ES-1901.00755
- [18] Krysander, M., Åslund, J., & Nyberg, M. (2008). An efficient algorithm for finding minimal overconstrained subsystems for model-based diagnosis. IEEE Transactions on Systems, Man, and Cybernetics-Part A: Systems and Humans, 38(1), 197–206. https://doi.org/10.1109/TSMCA.2007.909555
- [19] Düştegör, D., Frisk, E., Cocquempot, V., Krysander, M., & Staroswiecki, M. (2006). Structural analysis of fault isolability in the DAMADICS benchmark. Control Engineering Practice, 14(6), 597–608. https://doi.org/10.1016/j.conengprac.2005.04.008
- [20] Svärd, C., Nyberg, M., & Frisk, E. (2013). Realizability constrained selection of residual generators for fault diagnosis with an automotive engine application. IEEE Transactions on Systems, Man, and Cybernetics: Systems, 43(6), 1354–1369. https://doi.org/10.1109/TSMC.2013.2258906
- [21] Page, E. S. (1954). Continuous inspection schemes. Biometrika, 41(1/2), 100–115. https://doi.org/10.2307/2333009
- [22] Nikiforov, I. V., & Basseville, M. (1993). Detection of abrupt change theory and application. Prentice-Hall. https://cir.nii.ac.jp/crid/1970586434835655743
- [23] Gustafsson, F. (2006). Statistical signal processing approaches to fault detection. IFAC Proceedings Volumes, 39(13), 24–35. https://doi.org/10.3182/20060829-4-CN-2909.00004
- [24] Fawcett, T. (2006). An introduction to ROC analysis. Pattern Recognition Letters, 27(8), 861–874. https://doi.org/10.1016/j.patrec.2005.10.010
- [25] Bequette, B. W. (1998). Process dynamics: Modeling, analysis, and simulation. Prentice Hall. https://madar-ju.com/storage/images/files/file_1738596412NCggU
- [26] Downs, J. J., & Vogel, E. F. (1993). A plant-wide industrial process control problem. Computers & Chemical Engineering, 17(3), 245–255. https://doi.org/10.1016/0098-1354(93)80018-I
- [27] Venkateswaran, S., Liu, Q., Wilhite, B. A., & Kravaris, C. (2022). Design of linear residual generators for fault detection and isolation in nonlinear systems. International Journal of Control, 95(3), 804–820. https://doi.org/10.1080/00207179.2020.1823020
- [28] Du, P., Venkidasalapathy, J. A., Venkateswaran, S., Wilhite, B., & Kravaris, C. (2023). Model-based fault diagnosis and fault tolerant control for safety-critical chemical reactors: A case study of an exothermic continuous stirred-tank reactor. Industrial & Engineering Chemistry Research, 62(34), 13554. https://doi.org/10.1021/acs.iecr.3c01205
- [29] Du, P., Wilhite, B., & Kravaris, C. (2025). Model-based fault diagnosis in closed-loop safety-critical chemical reactors: An experimental study. AIChE Journal, 71(9), e18906. https://doi.org/10.1002/aic.18906
- [30] Du, P., Ranjan, R., Wilhite, B., & Kravaris, C. (2026). Model-based fault diagnosis and fault tolerant control in safety-critical chemical reactors: An experimental study. AIChE Journal, 72(7), e70378. https://doi.org/10.1002/aic.70378
- [31] Virtanen, P., Gommers, R., Oliphant, T. E., Haberland, M., Reddy, T., Cournapeau, D., ..., & Van Mulbregt, P. (2020). SciPy 1.0: Fundamental algorithms for scientific computing in Python. Nature Methods, 17(3), 261–272. https://doi.org/10.1038/s41592-019-0686-2
- [32] Savitzky, A., & Golay, M. J. E. (1964). Smoothing and differentiation of data by simplified least squares procedures. Analytical Chemistry, 36(8), 1627–1639. https://doi.org/10.1021/ac60214a047